67 Mustang GTA 390 Fastback Restoration project begins

Any questions or suggestions regarding restorations
User avatar
Gavin RS
Posts: 1110
Joined: Wed 22 Aug 2007, 16:37
Location: Randpark Ridge Randburg South Africa
Contact:

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by Gavin RS » Wed 03 Dec 2014, 09:39

Hey Brennan

I think do the mods you want to give it more power and driveability, but keep it mostly original, Don't go the Eleanor route, that's only a movie car anyway.

at the end of the day it is a serious collector original car so a few decent mods and upgrades to bring it to more modern standards wont detract from value, it is your car anyway, besides as I said before you will more than likely keep the original parts you remove so that's cool, wake up that old 390 and burn some rubber, the Mustang needs to be driven as much as possible, don't worry about fuel, it dropped by over 60c a litre last night, every bit helps :D

Cant wait to keep an eye on this build, one of my favourite looking Mustangs for sure
1984 Rover Vandenplas V8 (Historic Race car)
1986 Rover 3500 Vitesse with 4.6lt from V8 Developments (UK Import Ex London Police Car)
1982 Rover SDS V8 manual
2009 Ford Territory ST,
2006 Ford Fiesta 1.6 Auto, daily driver

brennan67
Posts: 328
Joined: Fri 18 Jul 2014, 23:43

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by brennan67 » Mon 15 Dec 2014, 12:08

Howzit guys

Ok I have started shipping the car down this weekend.
This is how she looks to date in my garage :
IMG_3460.jpeg
IMG_3460.jpeg (94.6 KiB) Viewed 1783 times
Body is not too bad, biggest problem is that some idiot decided the back quarter panels needed to be flared out. I will need to repair that. Looking for some advice here on the best way to do that, so you fabricator guys, what do you think my best options are here?
There are body repair panels from the entire rear quarter including the roof section above the vents, quarter panels from the top of fender "hip line" or patch panels that would require say 20cm weld around curve of the wheel opening. My thoughts are to try and minimise the amount of welding and the smaller repair the better ?
IMG_3463.jpeg
IMG_3463.jpeg (89.48 KiB) Viewed 1783 times
IMG_3464.jpeg
IMG_3464.jpeg (83.51 KiB) Viewed 1783 times
IMG_3466.jpeg
IMG_3466.jpeg (82.38 KiB) Viewed 1783 times
Rear end is in good shape, no rust or damage in the boot or rear, roof looks good,
IMG_3468.jpeg
IMG_3468.jpeg (76.77 KiB) Viewed 1783 times
Interior body is rust free, dont you love that red crushed velvet interior panels?? Foor panels look in good shape
IMG_3473.jpeg
IMG_3473.jpeg (80.16 KiB) Viewed 1783 times
I have decided I am going factory original numbers matching parts, colours, details etc on this car. So I will be painting and detailing engine, underbody, suspension, drive train etc according.
So next steps are to list all parts needed and start buying... :lol:
Then strip out rest of car, suspension and steering is left to do.
Weld up a frame with wheels so we can get her to move around and get underneath.

Then in the new year to find blaster who can soda blast underneath, inside and external down her in Durban who I can trust. I have a few I will need to check out.

User avatar
Gavin RS
Posts: 1110
Joined: Wed 22 Aug 2007, 16:37
Location: Randpark Ridge Randburg South Africa
Contact:

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by Gavin RS » Mon 15 Dec 2014, 12:45

Awsome :D
1984 Rover Vandenplas V8 (Historic Race car)
1986 Rover 3500 Vitesse with 4.6lt from V8 Developments (UK Import Ex London Police Car)
1982 Rover SDS V8 manual
2009 Ford Territory ST,
2006 Ford Fiesta 1.6 Auto, daily driver

User avatar
ZA Perana
Posts: 7289
Joined: Sun 15 Jul 2007, 18:01
Location: Cape Town

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by ZA Perana » Mon 15 Dec 2014, 13:03

Barring the flares the body looks very, very good.
Alfa GTV 3.0
Ford Capri Perana V8
Chevy Lumina Supercharged

Wait not for tomorrow to do what can be done today, live each day for one knows not what the next day may hold.

User avatar
IndianaJones
Posts: 4859
Joined: Sun 23 Aug 2009, 17:39
Location: Citrusdal, RSA

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by IndianaJones » Mon 15 Dec 2014, 13:49

Why the red velvet? Your Marti report said Dark Moss Green with black bucket seats.

brennan67
Posts: 328
Joined: Fri 18 Jul 2014, 23:43

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by brennan67 » Mon 15 Dec 2014, 14:20

IndianaJones wrote:Why the red velvet? Your Marti report said Dark Moss Green with black bucket seats.
lol... I can only think it was a "local upgrade" made over a few bottles of brandy and coke. trust me its going.. I would have loved to have seen the finished product the day the manne did the said upgrade. priceless..

brennan67
Posts: 328
Joined: Fri 18 Jul 2014, 23:43

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by brennan67 » Mon 05 Jan 2015, 14:08

Ok did some work on the FB over the holidays,

Not much but a start.. pulled her out, had a bit of a frame welded up so she is high off the ground but can still wheel in and out of garage.

Stripped off all bolt on parts, now we just left with the body shell. Had a good look at what we working with and it seems the floor pan has been patch repaired before with a plate over the passenger side floor pan. These mustangs were prone to water getting into the cowl and down onto the carpet and then water into the floor pan by your feet. So both sides have a bit of rust. back floor pan also some pinholes and pitting. The Kimberly boys also decided it would be better to have a handbrake on the gearbox tunnel than on the dash so they hacked a hole in there. probably to so lekker handbrake turns right ??

Lower firewall also got a bit of rust but easily fixed.

I have made the decision to replace the entire floor pan as I am doing a concours original restoration here and will be buying this from Scott drake as I dont want weld in patch seams all over the floor pan. I want anybody working underneath the car to say wow this thing is straight ! 8)
14666_280_210_l_n.jpg
14666_280_210_l_n.jpg (11.77 KiB) Viewed 1714 times
Attachments
IMG_3524.jpg
IMG_3524.jpg (107.24 KiB) Viewed 1714 times
IMG_3514.jpg
IMG_3514.jpg (114.83 KiB) Viewed 1714 times
IMG_3512.jpg
IMG_3512.jpg (123.17 KiB) Viewed 1714 times
IMG_3511.jpg
IMG_3511.jpg (115.82 KiB) Viewed 1714 times
IMG_3508.jpg
IMG_3508.jpg (125.62 KiB) Viewed 1714 times
IMG_3507.jpg
IMG_3507.jpg (118.61 KiB) Viewed 1714 times
IMG_3506.jpg
IMG_3506.jpg (127.67 KiB) Viewed 1714 times

User avatar
ZA Perana
Posts: 7289
Joined: Sun 15 Jul 2007, 18:01
Location: Cape Town

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by ZA Perana » Mon 05 Jan 2015, 19:22

Age considered the floor pan doesn't look too bad, considering the lives some of these cars had its amazing some survived at all!
Alfa GTV 3.0
Ford Capri Perana V8
Chevy Lumina Supercharged

Wait not for tomorrow to do what can be done today, live each day for one knows not what the next day may hold.

brennan67
Posts: 328
Joined: Fri 18 Jul 2014, 23:43

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by brennan67 » Fri 09 Jan 2015, 13:22

Floor pan is not too bad but its not perfect either, we have cut out old patch done on passenger side about A3 size. Drivers side is better but not perfect.
I will take some photos ever weekend and upload.

The good news is today I have spent a large sum of $$ on body parts, all new suspension parts, power steering and brakes. These parts will ship via sea freight and I will probably get them in March. This will be everything to complete the body and sheetmetal, complete underside of car including all new brakelines and hoses, drums, callipers, disks, all new suspension control arms, bushings, sway bars, shocks, power steering lines and hardware you name it. Even spent R8000 on bolt kits for the body panels and chassis :? Each part is packaged and labeled separately so you got the right bolt for the right part. I must be mad but I figure the time wasted trying to find the right bolts and then going do 101 trips to the nut and bolt shop its well worth it !
mck67dcbb.jpg
Master chassis bolt kit
mck67dcbb.jpg (138.82 KiB) Viewed 1665 times
mbk3s.jpg
mbk3s.jpg (250.23 KiB) Viewed 1665 times
I am now excited.. :D :D :D

brennan67
Posts: 328
Joined: Fri 18 Jul 2014, 23:43

Re: 67 Mustang GTA 390 Fastback Restoration project begins

Post by brennan67 » Fri 09 Jan 2015, 13:41

Whilst I am on the underside of the car, what you guys think ?

I am going the concours original route right, so that requires I paint the underside of the car in red oxide with overspray on the sides like they did back in the factory.
here are some pics of concours original restorations in the USA of what the guys have done. The question is do I intentionally crate overspray :lol: :lol: ??
Attachments
exterior_13.jpg
exterior_13.jpg (83.51 KiB) Viewed 1664 times
exterior_07.jpg
exterior_07.jpg (97.44 KiB) Viewed 1664 times
exterior_14.jpg
exterior_14.jpg (87.61 KiB) Viewed 1664 times
exterior_06.jpg
exterior_06.jpg (109.06 KiB) Viewed 1664 times
exterior_10.jpg
exterior_10.jpg (82.3 KiB) Viewed 1664 times

Post Reply

Social Media

     

Who is online

Users browsing this forum: No registered users and 13 guests